4 minutes reading time (751 words)

Mastering MONTAGE: Three Way Super Knob Transition

Mastering MONTAGE: Three Way Super Knob Transition
Want to know how to switch between PARTS in a hands free fashion with your MONTAGE? In this lesson from Bad Mister, add three PARTS switched via Foot Controller/Super Knob to your repertoire of skills. Feel free to expand on this with sounds of your own choosing. Check it out below!
  
You'll find a ZIPPED DOWNLOAD at the very bottom of the article. Unzip the .X7B File. Place the file "3 on FC SuperKnob.X7B" in a folder on your computer where you keep your Montage Files. Use "MONTAGE Connect" to bulk this PERFORMANCE from your computer to your MONTAGE's Edit Buffer. This will allow you to play and explore it without having to overwrite anything in your MONTAGE. While in the Edit Buffer, you can explore it, study it, and if you wish edit it as you like and then STORE it.

3onFC SN1

This Performance can be morphed either directly with the Super Knob or with an FC7 plugged into the Foot Controller 2 jack (which has been set to "Super Knob").

You can use the Super Knob to morph between PARTS. Here is a quick example, where PART 1 is an Acoustic Piano, PART 2 is a String/Brass/Bell combination (Brass on MW, Bell above C4 on A.Sw1), and PART 3 is an Electric Piano. The Super Knob at 7 o'clock to 10 o'clock is the Acoustic Piano, there is a small region of overlap to the Strings sound (raise MW to bring in Brass with Strings), another small region of overlap to the Electric Piano around the 2 o'clock position. You can see how this is accomplished in the screenshots of the CURVE TYPES (shown in the screenshots below).

Super Knob position has been captured in the following SCENES (as an alternate method of recalling sounds):
SCENE 1 = Acoustic Piano
SCENE 2 = Acoustic Piano/Strings
SCENE 3 = Strings
SCENE 4 = Strings/Electric Piano
SCENE 5 = Electric Piano

PART 1: CFX PopStudioGrand
CURVE TYPE:
Threshold
POLARITY: Bi
RATIO: -64
PARAMETER 1: 3
PARAMETER 2: 1

These settings contour PART 1's response so that it is loud initially but as you increase the AssignKnob 1, the Volume drops off to nothing. VOLUME has been assigned to the position of Assign Knob 1. As Knob 1 is increased the Acoustic Piano fades out.

Part1Curve


PART 2: St Ensemble K

CURVE TYPE:
Bell
POLARITY: Bi
RATIO: +63
PARAMETER 1: 4
PARAMETER 2: 2

These setting are programmed so that PART 2 is silent initially, but as you increase the value of AssignKnob 2, it is loudest in the middle and drops off to nothing at maximum. VOLUME has been assigned to the position of Assign Knob 2.

Part2Curve


PART 3: Dyno Chorus MW
CURVE TYPE:
Sigmoid
POLARITY: Bi
RATIO: +63
PARAMETER 1: 0
PARAMETER 2: 3

These setting are programmed so that Part 3 is silent until you reach about 2/3 of the way through the travel of the knob. VOLUME has been assigned to the position of Assign Knob 3.

Part3Curve

On the upper COMMON/Audio Level of the EDIT architecture is where the 'link' between the PART's Assignable Knobs to the Super Knob movement is made: This means as you turn the Super Knob from minimum toward maximum you are also turning Part 1's AssignKnob 1, Part 2's AssignKnob 2 and Part 3's AssignKnob 3, simultaneously. You can adjust the Curve Parameters so that you get the appropriate amount of overlap or no overlap, as you may desire. You can even create your own custom USER CURVES, if necessary. The two "PARAM" values help you shape the CURVE to your needs. Please experiment - adjusting the cross fade is a matter of taste and what you find comfortable musically speaking.

SNassign

The above screenshot shows on the top COMMON/AUDIO level of editing that: 
PART 1 ASSIGN 1 = Part 1's Assignable Knob 1 is linked to the Super Knob movement. 
PART 2 ASSIGN 2 = Part 2's Assignable Knob 2 is linked to the Super Knob movement
PART 3 ASSIGN 3 = Part 3's Assignable Knob 3 is linked to the Super Knob movement

Notice I have labeled the Assign Knobs using the "Display Name" box, this way you know what each Assign Knob is doing. (Shown: "Destination 1" is currently selected and the Display Name = A.Pno Vol).

Ready to get started? Download the file at bottom of this article. 

Want to discuss this more? Join the conversation on the Forum here.

And stay tuned to gain more skills for mastering your MONTAGE!

Synth 101 - Lesson 3: Methods of Synthesis
Connecting MONTAGE and Logic Pro X

Related Posts

By accepting you will be accessing a service provided by a third-party external to https://yamahasynth.com/

2018 © Yamaha Corporation of America and Yamaha Corporation. All rights reserved.