Setting up to record to Cubase via FireWire on a Windows computer - here's what you need to know.
A quick setup guide to get going with Cubase and your Motif XF via the FW16E (firewire) option:
Download and install the following items:
_ Yamaha Steinberg FW Driver version 1.6.6 (or later) for your particular Windows operating system
_ Motif XF Extension version 1.1.1 (or later) for Windows
The Motif XF Extension is an addition to Cubase that will allow it to recognize the Motif XF ports by name, and it will automatically do much of the audio and MIDI setup (like assigning Remote Control Device ports, and upon launch you will be asked if you want to use the Yamaha Steinberg FW driver as your ASIO driver, etc). When you are using the Motif XF with the Yamaha Steinberg FW driver (YSFW) you need to verify the following settings in your Motif XF:
Press [UTILITY] Press [F5] CONTROL Press [SF2] MIDI Ensure that the MIDI IN/OUT = FW Press [STORE] to write this preference to your Flash ROM.
Now, let’s setup your Windows computer:
Go to CONTROL PANEL
Depending on your default view (Category, Large icon, Small icon) you need to find the Yamaha Steinberg FW icon. It will be listed under the heading “Hardware and Sound” if you have the “Category” view. If you have the LARGE or SMALL icon view you will see it listed as “Yamaha Steinberg FW”
Double click the icon to open the Yamaha Steinberg FW control panel.
Here you will be able to set the Sample Rate (44.1kHz, 48kHz, 88.2kHz or 96kHz), the Word Clock Master (Motif XF7), and the Clock Source (Internal)
Click on the WDM > AUDIO ROUTING option. Here the Driver can be used for your Windows applications (this is not necessary for Cubase, you will setup for Cubase within that program) but if you would like your Windows Media Player or other Windows audio applications (games, etc) to use use your Motif XF studio system (that is, route audio via the XF audio oututs) set the AUDIO ROUTING here to use the “Motif XF Main L/R” Outputs.
Click on the tab(s) that identifies your connected device(s): Motif XF7
The current IEEE1394 Firmware version of your FW16E will be shown. This should read: V1.08 currently
This sets your Motif XF as your soundcard for your computer. Expect audio output to be sent to the sound system connected to the main LEFT/RIGHT outputs of the Motif XF.
Because you have installed the Motif XF Extension, Cubase will ask you if you want to use the Yamaha Steinberg FW driver as your ASIO driver.
Go to DEVICES > DEVICE SETUP… > MIDI > MIDI Port Setup
Here you will be able to select the device(s) that will be your MIDI controller. Typically this is either your Motif XF keyboard (Motif XF Main) or any MIDI controller connected to its back panel Motif XF MIDI IN jack.
Make sure that only these devices are marked in the “In ‘All MIDI Inputs’” column
You do not want to mark the Motif XF REMOTE port in the In All MIDI Inputs column. Remote Control commands must be kept discreet, so as not to interfere with normal music performance. In the next folder “REMOTE DEVICES” highlight the Motif XF item. It will be assigned as your Remote Control device and the MIDI IN and MIDI OUT ports will be assigned.
Move down to the VST AUDIO SYSTEM item and verify that the Yamaha Steinberg FW is selected as the ASIO DRIVER.
The option just below VST AUDIO SYSTEM will be “Yamaha Steinberg FW”. If you highlight that you will see the CONTROL PANEL where you can set your buffer size.
The screen shot above shows the 16 Audio OUTPUT buses available from the Motif XF. They are seen as audio (IN) inputs to Cubase. You will see the PORTS listed by their names (if you have properly installed the Motif XF Extension). The first are the MAIN Left/Right OUTPUTS of the Motif XF arriving in Cubase as “Motif XF Main L” and “Motif XF Main R”. You will see the word “Active” in the STATE column - this is a status report and indicates that currently these inputs are in use by Cubase. The “Inactive” status on the “Motif XF 1” - “Motif XF 14” simply means that as of yet, nothing is assigned to use those inputs into Cubase. You do not have to worry about changing these to active, they will change when you actually assign something to use these inputs into the Cubase program. (That assignment typically is made when you decide to route a Motif XF PART to an assignable output. At some point you might connect a microphone to the XF or you may have cause to route a single instrument to its own track. You do so by re-routing the PART to a FireWire bus OUTPUT. By default all XF PARTS are routed to the main L/R outputs).
For example, if you go to VST CONNECTIONS > INPUTS and create an input (ADD BUS) that was set so that AUDIO DEVICE = Yamaha Steinberg FW ASIO driver, and the DEVICE PORTS = Motif XF 1, and Motif XF 2, then the STATE would change to ‘active’. Once an INPUT Connection is used, it becomes unavailable for use elsewhere. So that status of the INPUT is always reported here. Please note that there are 16 INPUTS to Cubase (16 OUTPUTS from the Motif XF) and that they are labeled Main Left, Main R followed by Motif XF 1 through Motif XF 14. That is a total of 16. The first two are the main left/right stereo, followed by fourteen individual sends that can be configured as odd/even stereo pairs or as individual mono sends.
Below the 16 INPUTS to Cubase, 6 AUDIO OUTPUTS are shown as three pair of audio outs that return to the Motif XF:
Motif XF Main L / Motif XF Main R = sends signal from Cubase to the main left/right audio outputs of the Motif XF. remember the XF is your computer’s soundcard when you are using the YSFW driver as your ASIO Driver. The Main L/R outputs are the 1/4” outputs found on the back panel of the XF and these should be connected to your main sound system (monitor speakers, mixer, etc).
Motif XF FW L / Motif XF FW R = sends signal from Cubase to the internal Motif XF mixer where you can combine this return with your current internal mix or you can route the return to the XF’s Integrated Sampler. The Firewire return has its own audio channel with access to Volume, Pan, and the SYSTEM EFFECTS.
Motif XF ASGN L / Motif XF ASGN R = sends signal from Cubase to the Assignable left/right audio outputs of the Motif XF. This signal can be sent a second set of monitor speakers or used to create a separate monitor mix. This is very useful when you have additional musicians in a record situation and you require a separate headphone system. You can feed this output mix to an external headphone amplifier system and deliver a separate discreet mix (the full version of Cubase 5 or 6 gives you an opportunity to setup such separate STUDIO SENDS if you require this functionality).